powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com photo voltaic ipm h-bridge + 1 chopper 75 amperes/600 volts PM75B5L1C060 1 03/11 rev. 0 description: powerex intellimod? photo voltaic intelligent power modules are isolated base modules designed for single phase power switching applications. built-in control circuits provide optimum gate drive and protection for the igbt and free-wheel diode power devices. features: complete output power circuit gate drive circuit protection logic C short circuit C over temperature using on-chip temperature sensing C under voltage low loss using full gate cstbt igbt chip applications: pv inverters pv ups pv power supplies ordering information: example: select the complete part number from the table below -i.e. PM75B5L1C060 is a 600v, 75 ampere pv-ipm. type current rating v ces amperes volts (x 10) pm 75 60 outline drawing and circuit diagram a d e f f f f g g g g g g g g g g g g g b c g n p m q k j l l l l l f t u v c s (19 typ.) r h (2 typ.) 1 5 9 13 b p n u v w 19 f o 17 v n 14 v n1 11 nc 8 v vp1 2 u fo 6 v fo 5 v vpc 3 u p 7 v p 9 nc 10 nc 12 nc 1 v upc 4 v up1 16 u n 15 nc 18 w n 13 v nc terminal code v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot p u nc 1.5k 1.5k 1.5k v w n b v cc s i gnd gnd out f o in ot v cc s i gnd gnd out f o in ot u n f o v nc w n v n1 v n nc nc nc nc v vpc v p v fo v vp1 v upc u p u fo v up1 dim. inches millimeters a 3.54 90.0 b 1.97 50.0 c 0.98 25.0 d 3.15 80.0 e 0.20 5.0 f 0.39 10.0 g 0.08 2.0 h 0.17 dia. 4.3 dia. j 0.81 20.5 k 0.91 23.0 dim. inches millimeters l 0.47 12.0 m 0.012 0.3 n 0.57 14.6 p 0.26 6.7 q 0.02 0.5 r 0.56 14.2 s 0.02 sq. 0.5 sq. t 0.08 2.0 u 0.51 13.0 v 0.65 16.5
PM75B5L1C060 photo voltaic ipm h-bridge + 1 chopper 75 amperes/600 volts powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com 2 03/11 rev. 0 absolute maximum ratings, t j = 25c unless otherwise specifed characteristics symbol PM75B5L1C060 units power device junction temperature t j -20 to 150 c storage temperature t stg -40 to 125 c mounting torque, m4 mounting screws (typical) 15 in-lb module weight (typical) 135 grams supply voltage, surge (applied between p-n) v cc(surge) 500 volts operation of short circuit protections v cc(prot.) 450 volts (applied between p-n, v d = 13.5 ~ 16.5v, inverter part, t j = 125c start) isolation voltage (60hz, sinusoidal, rms, charged part to base, ac 1 minute) v iso 2500 volts inverter part collector-emitter voltage (v d = 15v, v cin = 15v) v ces 600 volts collector current (t c = 25c) i c 75 amperes collector current (pulse) i crm 150 amperes total power dissipation (t c = 25c) p tot 201 watts emitter current (t c = 25c, fwdi current) i e 75 amperes emitter current (pulse, fwdi current) i erm 150 amperes converter part collector-emitter voltage (v d = 15v, v cin = 15v) v ces 600 volts collector current (t c = 25c) i c 75 amperes collector current (pulse) i crm 150 amperes total power dissipation (t c = 25c) p tot 201 watts emitter current (t c = 25c, fwdi current) i e 75 amperes emitter current (pulse, fwdi current) i erm 150 amperes diode forward current (t c = 25c) i f 75 amperes diode rated dc reverse voltage (t c = 25c) v r(dc) 600 volts control part supply voltage (applied between v up1 -v upc , v vp1 -v vpc , v n1 -v nc ) v d 20 volts input voltage (applied between u p -v upc , v p -v vpc , u n - v n - w n -br-v nc ) v cin 20 volts fault output supply voltage v fo 20 volts (applied between u fo -v upc , v fo -v vpc , f o -v nc ) fault output supply current (sink current at u fo , v fo , f o terminals) i fo 20 ma
PM75B5L1C060 photo voltaic ipm h-bridge + 1 chopper 75 amperes/600 volts powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com 3 03/11 rev. 0 electrical and mechanical characteristics, t j = 25c unless otherwise specifed characteristics symbol test conditions min. typ. max. units inverter part collector-emitter saturation voltage v ce(sat) v d = 15v, i c = 75a, v cin = 0v, 2.2 2.7 volts pulsed, t j = 25c v d = 15v, i c = 75a, v cin = 0v, 2.2 2.7 volts pulsed, t j = 125c emitter-collector voltage v ec i e = 75a, v d = 15v, v cin = 15v 2.4 3.3 volts switching times t on 0.1 0.5 1.2 s t rr v d = 15v, v cin = 0 ? 15v 0.1 0.2 s t c(on) v cc = 300v, i c = 75a, 0.15 0.3 s t off t j = 125c, inductive load 1.1 2.0 s t c(off) 0.2 0.4 s collector-emitter cutoff current i ces v ce = v ces , v d = 15v, v cin = 15v, t j = 25c 1.0 ma v ce = v ces , v d = 15v, 10 ma v cin = 15v, t j = 125c converter part collector-emitter saturation voltage v ce(sat) v d = 15v, i c = 75a, v cin = 0v, 2.2 2.7 volts pulsed, t j = 25c v d = 15v, i c = 75a, v cin = 0v, 2.2 2.7 volts pulsed, t j = 125c emitter-collector voltage v ec i e = 75a, v d = 15v, v cin = 15v 2.4 3.3 volts diode forward voltage v fm i f = 75a 2.4 3.3 volts switching times t on 0.1 0.5 1.2 s t rr v d = 15v, v cin = 0 ? 15v 0.1 0.2 s t c(on) v cc = 300v, i c = 75a, 0.15 0.3 s t off t j = 125c, inductive load 1.1 2.0 s t c(off) 0.2 0.4 s collector-emitter cutoff current i ces v ce = v ces , v d = 15v, v cin = 15v, t j = 25c 1.0 ma v ce = v ces , v d = 15v, 10 ma v cin = 15v, t j = 125c
PM75B5L1C060 photo voltaic ipm h-bridge + 1 chopper 75 amperes/600 volts powerex, inc., 173 pavilion lane, youngwood, pennsylvania 15697 (724) 925-7272 www.pwrx.com 4 03/11 rev. 0 electrical and mechanical characteristics, t j = 25c unless otherwise specifed characteristics symbol test conditions min. typ. max. units c ontrol part circuit current i d v d = 15v, v cin = 15v, v n1 -v nc 6.5 12 ma v d = 15v, v cin = 15v, v *p1 -v *pc 1.6 4 ma input on threshold voltage v th(on) applied between u p -v upc , 1.2 1.5 1.8 volts input off threshold voltage v th(off) v p -v vpc , u n - v n - w n -br-v nc 1.7 2.0 2.3 volts short circuit trip level sc -20c t j 125c, v d = 15v 112 amperes short circuit current delay time t off(sc) v d = 15v 0.2 s over temperature protection ot trip level 135 c (detect temperature of igbt) ot (hys) hysteresis 20 c supply circuit under-voltage protection uv t trip level 11.5 12.0 12.5 volts (-20c t j 125c) uv r reset level 12.5 volts fault output current* 2 i fo(h) v d = 15v, v fo = 15v 0.01 ma i fo(l) v d = 15v, v fo = 15v 10 15 ma fault output pulse width* 2 t fo v d = 15v 1.0 1.8 ms thermal characteristics, t j = 25c unless otherwise specifed characteristic symbol condition min. typ. max. units junction to case thermal resistance r th(j-c)q inverter igbt (per 1 element)* 1 0.62 c/watt r th(j-c)d inverter fwdi (per 1 element)* 1 1.06 c/watt r th(j-c)q converter igbt (per 1 element)* 1 0.62 c/watt r th(j-c)d converter fwdi (per 1 element)* 1 1.06 c/watt r th(j-c)d converter diode (per 1 element)* 1 1.06 c/watt contact thermal resistance r th(c-f) case to fin (per 1 element)* 1 , 0.060 c/watt thermal grease applied r ecommended conditions for u se characteristic symbol condition value units inverter supply voltage v cc applied across p-n terminals 450 volts control supply voltage* 3 v d applied between v up1 -v upc , 15.0 1.5 volts v vp1 -v vpc , v n1 -v nc input on voltage v cin(on) applied between u p -v upc , 0.8 volts input off voltage v cin(off) v p -v vpc , u n - v n - w n -br-v nc 9.0 volts pwm input frequency f pwm using application circuit input signal of ipm, 20 khz 3-phase sinusoidal pwm vvvf inverter arm shoot-through blocking time t dead for ipms each input signals 2.0 s *1 when using this value, r th(s-a) should be measured just under the chips. *2 fault output is given only when the internal sc, ot and uv protections schemes of either upper or lower devide operate to protect it. fault output of sc protection given pulse. fault output of ot, uv protection given pulse while over trip level. *3 with ripple satisfying the following conditions: dv/dt swing 5v/s ; variation 2v peak-to-peak.
|
